Ducati narrow-case single parts

[flynbulldog]

Vintage Ducati narrow-case single parts
________________________________________
$200 Narrow case frame (Dirty but straight & unmolested)
$1000 Rebuildable 1965 250cc narrow case engine from scrambler (non-desmo)
$800 Shouldered Borrani aluminum 250 wheels (front & rear) complete with race tires, stainless spokes, and brakes (very nice condition)
$100 Scrambler Parts (very rough condition):
• Rear fender
• Pair shrouded shocks
• Kickstand and engine mount
• Front foot pegs
• Kickstarter
• Misc. front fork tubes, springs, parts (mostly junk)
• Coil
• Throttle tube and cable
• Exhaust head pipe
• Pair of unshrouded shocks
• Rocker shifter (bent)
• Rear brake switch
• 35 mm Marzocchi single fork lower leg
$50 Misc engine gaskets, shims, o-rings, seals (New)
$10 250 battery hold down strap (New)
$40 Kickstart arm
$5 Pair new points and condenser
$10 Narrow case 250 clutch rods and balls
$100 Set of new engine bearings
$20 Points cover kit (aftermarket)
$20 new exhaust collar
$50 Pair of valve covers
$50 Internal bits for kickstarter
$10 Gear shift lever
$150 High performance double I-beam connecting rod
$50 New wide case swing arm pin
$10 New or redone chain guard
$50 One 250 flywheel and stater
$75 One 250 head (bare head)



$450 All new parts to rebuild a 250 head
• Set of coil valve springs
• Two cams (used)
• New stainless steel 40mm & 36mm valves
• New bronze valve guides
• Cam bearing case end
•
$350 Fresh cylinder with new Venolea 12.5:1 compression piston and new rings
$30 One narrow case clutch basket

Let me know if you need photos. Buyer pays shipping, I'll pay the paypal fee
Guys some of this stuff is in great condition, some in service-able condition, and some is just nasty. Let me know what you need and we'll talk.

If you want the whole lot I’ll make you a hell of a deal but you have to work out pick-up or shipping. I’m near Castle Rock Colorado

[a_kress]

$50 One 250 flywheel and stater
$10 Gear shift lever
$10 Narrow case 250 clutch rods and balls
$50 Internal bits for kickstarter

I'm really interested in these. Are these bit still available? Can you send me an email (akress@akress.com)?

[Stearman22]

What are you asking for your brake switch? can you send me a pic of.
Camsports1@sbcglobal.net

Thanks,
Jeff

[MayerMR]

You don't happen to have a n/c centerstand do you?

Thanks!

-Matt

[Adam]

Hi, I'd be interested in the kickstand and engine mount plate. Can I get a picture of that please (if still available)?

Thanks
Adam

[JJJ12345]

I would be interested in the shift lever. Any pics? Thanks.

[krupp13]

Quick update...

My friend Flynbulldog is in the process of relocating across the country and rather than packing all the parts up to ship, he has sold them all to me locally. He had not sold any from the above list, so I will extend the offer and prices that he listed above. I will try to reply with a PM for the above guys soon. Everything is catalogued and bagged up, so please let me know if you are interested in anything.

Best regards,

Jeff

[jevincj]

How about the rear fender?

[Octane]

Any idea what shipping would be like on the N/C frame and 250 motor to either Australia or Japan?
I'm tempted but I think shipping would be a dealbreaker.

[planepaul]

Hi, am looking for a kickstart lever assembly that will fit a Monza Junior. Also interested in the points and condenser, the points cover kit and maybe the shift lever. Am I too late? Thanks